CLASSES & RULES

Classes:

RULES:

Please note; these rules are assembled for simplicity, RCRA based rules will still be enforced if we believe an advantage is gained by "outlaw" activities. Mistakes will be excused, however, actions taken to cheat will be strictly dealt with. We race for fun, let's keep it fun for everyone by allowing "relaxed" ruling.

 

ALL 4WD TOURING CARS:

  • Minimum Weight: 1320g

  • Bodyshell: 4 door to ROAR/EFRA/BRCA/IFMAR approved and compliant with GBS (Global Body Specification). As of 1st Jan 2020, all bodyshells must be 85 grams minimum in race trim.

  • Li-Po’s: 2S ROAR/EFRA/BRCA/IFMAR Approved or CE certified

  • Discharge banks: Not allowed

  • Max Batt Voltage: 8.40 (only 21.5T and 13.5T checked in pre-race tech)

  • Max Charging Rate: 12 amps

  • Control Tyres: Sweep Racing EXP-30R2ATS (Except for Round 5 Carpet)

  • Control Additive: ATS Additive

21.5T STOCK:

  • Minimum FDR: 2.8 - You can run at/or higher than 2.8, but not below it.

  • R1 Wurks AARCMCC 21.5T Control Motor set @ 2400kV. Available for purchase for $120 or Rent for $25 per series race.

  • Blinky ESC (Zero Timing)

  • 3 sets of tyres for the event to use how you please

13.5T PRO STOCK:

  • Minimum FDR: 3.8 - You can run at/or higher than 3.8, but not below it.

  • R1 Wurks 13.5T Control Motor set @ 3900kV. Available for purchase for $120 or Rent for $25 per series race.

  • Blinky ESC (Zero Timing)

  • 3 sets of tyres for the event to use how you please

MODIFIED TOURING:

  • Any brushless motor allowed

  • 4 sets of tyres for the event to use how you please

17.5GT:

  • Minimum FDR: 3.5 - You can run at/or higher than 3.5, but not below it.

  • Muchmore Fixed Timing 17.5T GT Motor as ran at all events

  • Blinky ESC (Zero Timing)

  • 3 sets of tyres for the event to use how you please

  • Must use approved GT Bodyshells (Protoform, Zoo Racing, Bittydesign & Pitlane)

  • We will have motors available for hire, please indicate on the entry form if you need one!

1/12th STOCK:

  • Minimum Weight: 730g

  • Bodyshell: IFMAR, EFRA, ROAR or BRCA Approved

  • Motor: Non-controlled 13.5T Brushless (ROAR/EFRA Approved)

  • Battery: 3.7v 1 Cell LiPo (ROAR/EFRA Approved)

  • Discharge banks: Not allowed

  • Max Batt Voltage: 4.20v (checked in pre-race tech)

  • Max Charging Rate: 12 amps

  • Controlled Tyres: Ulti ATS compound - maximum of 3 sets for all racing (7 sets for the indoor round)

  • Controlled Additive: ATS Additive

1/12th MODIFIED:

  • Minimum Weight: 730g

  • Bodyshell: IFMAR, EFRA, ROAR or BRCA Approved

  • Motor: Any Brushless Motor

  • Battery: 3.7v 1 Cell LiPo (ROAR/EFRA Approved)

  • Discharge banks: Not allowed

  • Max Batt Voltage: 4.20v (checked in pre-race tech)

  • Max Charging Rate: 12 amps

  • Controlled Tyres: Ulti ATS compound - maximum of 5 sets for all racing (7 sets for the indoor round)

  • Controlled Additive: ATS Additive

FORMULA 1:

Click here for rules

Controlled Tyres: None (Except for the indoor round)

Controlled Additive: ATS Additive 

PRO 10:

  • Minimum Weight: TBA

  • Bodyshell: 235mm

  • Motor: Any Brushless Motor

  • Battery: 7.4v 2 Cell LiPo (ROAR/EFRA Approved)

  • Discharge banks: Not allowed

  • Max Batt Voltage: 8.40v (checked in pre-race tech)

  • Max Charging Rate: 12 amps

  • Controlled Tyres: None

  • Controlled Additive: ATS Additive

TCR FWD:

  • No minimum weight

  • Bodyshell: Eligible body shells are reasonable scale representations of any existing front-wheel drive sedan/hatchback or wagon, with a minimum allowable roof height of 125mm measured at the highest point on the roof. Wings must be supplied with the original body and must be painted, not clear. Body must be cut to original defined manufactured lines.

  • Chassis: Any 1/10 scale FWD fully independent suspension chassis, dimensions and specs as per RCRA/ISTC guidelines. 

  • Motor & ESC Combo: Must be either the Hobbywing Max 10 Combo - 60amp ESC (model No 30102602) & 3300kv Motor model No 30402600 (Same as a mini combo)

  • Or you can use Hobbywing XERUN XR10 Combo - ZERO Spec ESC, with a 17.5 Juststock 3650 G2.1 Stock Motor.

  • Battery: 7.4v 2 Cell LiPo (ROAR/EFRA Approved)

  • Discharge banks: Not allowed

  • Max Batt Voltage: 8.40v (checked in pre-race tech)

  • Max Charging Rate: 12 amps

  • Controlled Tyres: 3 sets of tyres for the event to use how you please

  • Wheel must have spokes/holes as manufactured, no flat dish wheels

  • Controlled Additive: ATS Additive

VTA (Vintage TRANSAM):

  • Chassis

ISTC 4WD as per RCRA rule 9.5  with AusVTA amendments. The Chassis must not be shaped to gain an aerodynamic advantage. In principle, the underside of the chassis must be flat and parallel  Aerodynamic shaped parts (splitters/diffusers/tunnels/etc) may not be fitted to the chassis.

  • Motor

Any ROAR BRCA or RCRA 21.5 approved motor.

  • ESC

Speed Controllers as per ROAR BRCA lists. Stock- Blinky mode only. Non-Boosted

  • Body Shell

Any 200mm pre-1990 model, 2 door or 4 door road race car.

Pre 1990 ATCC/Bathurst style or VTA body (GT style Aero bodies are not allowed) 

The body must be trimmed to trim lines and all additional moulded items included with that specific body must be attached. If unsure check before racing.

Bodies considered outside the spirit of the class can be excluded.

Rear Spoiler/Ducktail
Bodies not moulded or fitted with a competitive rear spoiler ( PF 65 Mustang etc) can be custom fitted with a Lexan unit no higher than 16mm from the rear deck lid and chord length no greater than 20mm.  The sides of the spoiler can be a maximum width of the top of the rear quarter panels and should follow the contour of the quarter panel styling. 

A touring car wing can be heavily cut down and modified to achieve this but it is advised to also attach a rear reinforcement panel to the spoiler. Any moulded lexan VTA rear spoiler manufactured can be fitted but must follow rear quarter panel contours. 

A body pre-moulded with an existing competitive rear spoiler cannot be modified or added to.

  • Tyres

HPI tyre part No #4793 (Front) and #4797 (rear), using stock tyre insert provided with the tyre. Any HPI wheels designed to fit these tyres. Wheels and tyres designated as “Front” must be used as front tyres/wheels, “Rear” wheels/tyres must be used as rears. Some tyre tread must be visible. Grinding of the tyre is not permitted. 

PROTOFORM WHEELS TYRES ARE ALLOWED

  • Batteries

Any 2 cell Hard-cased Lipo packs with ROAR, BRCA, RCRA approval.

  • Charging & Voltage

Max Charging Rate: 12 amps

Max Batt Voltage: 8.40v (checked in pre-race tech) 

  • Gearing

Gearing is not restricted.

  • Weight

Minimum 1450 grams


 

CONTROL MOTORS

In order for your motor to be allowed to race, we will inspect to ensure all components are in the original condition. The motor will then receive an ATS Approved Motor Sticker. From then we will seal a single front motor screw to prevent the opening of the motor during the event, and then set the kV on the motor to the correct limit, tighten the end bell and seal a single screw so that the timing cannot be changed throughout the event! That's it. For Hire motors, they have already undergone this process, so you can simply arrive and drive.

 
 
 
 
 
 
 
 
 
 

CONTROL TYRES

  • Touring Car: Sweep Racing EXP-30R2ATS

  • 1/12th Scale: Ulti ATS Compound (X Super Soft Rear, J-Medium Front)

CONTROL ADDITIVE

Sign up to get the latest ats news

  • Facebook
  • YouTube

Found what you're looking for?

site by - tony mcmahon, cloudedhouse